Can I apply some type of filter like sharpening and blurring that is found on Image analysis window(processing) just via arcpy on a tiff file?
↧
Image analysis via arcpy
↧
ArcMap does not display correct paper size
Hi friends,
I am trying to work on a map template that is meant for A3 paper.
When I go into Page and Print Setup, select my printer (or any other capable printer for that matter) and select Size: A3, make sure that the "Use Printer Paper Settings" is checked... the Page Width and Height correctly display as 29.7cm and 42cm respectively.
However, when I look at the rules on the sides of my map, the rules show the page sizes as 30.2cm and 42.5cm respectively. It is giving me an extra .5cm in both height and width and is messing up my alignment to get everything printing properly.
Any idea how to fix this or is there something I am missing...
Thanks friends!
I am trying to work on a map template that is meant for A3 paper.
When I go into Page and Print Setup, select my printer (or any other capable printer for that matter) and select Size: A3, make sure that the "Use Printer Paper Settings" is checked... the Page Width and Height correctly display as 29.7cm and 42cm respectively.
However, when I look at the rules on the sides of my map, the rules show the page sizes as 30.2cm and 42.5cm respectively. It is giving me an extra .5cm in both height and width and is messing up my alignment to get everything printing properly.
Any idea how to fix this or is there something I am missing...
Thanks friends!
↧
↧
Opening the selected ArcMap document failed.
I have been working on a mxd in ArcMap 10.1. When I open it in ArcMap 10.2 on a different computer, it won't open and gives me an error message.
Opening the selected ArcMap document failed.
The data frames of the map document could not be read could not be read due to the following error:
0x80040111(ClassFactory cannot supply requested class)
The last successfully loaded component was: Unknow ProgID({0CA176CA-8014-454F-A641-B814AB525719})
The specified file does not contain a valid ArcMap document.
For this particular mxd, I use some functions from Production Mapping, such as Layout Window. I have Production Mapping installed in ArcGIS 10.1. But 10.2 doesn't. Could this causing the problem?
How to resolve such problem? Thanks in advance.
Best Regards,
Amy
Quote:
Opening the selected ArcMap document failed.
The data frames of the map document could not be read could not be read due to the following error:
0x80040111(ClassFactory cannot supply requested class)
The last successfully loaded component was: Unknow ProgID({0CA176CA-8014-454F-A641-B814AB525719})
The specified file does not contain a valid ArcMap document.
How to resolve such problem? Thanks in advance.
Best Regards,
Amy
↧
Exporting Map With Individual Projected Shapefiles (?)
Hello,
I am trying to export a map from ArcGis containing individual projected files.
I have purchased shape files which I assigned a coordinate system in ArcMap. What I wish to do is define the projection and project all files at once, and export all ESRI shape files as individual layers to import into a different GIS application.
I seem to be having difficulty doing this. Might anybody know how I can accomplish this?
Thanks and hope to hear from you soon,
Katie
I am trying to export a map from ArcGis containing individual projected files.
I have purchased shape files which I assigned a coordinate system in ArcMap. What I wish to do is define the projection and project all files at once, and export all ESRI shape files as individual layers to import into a different GIS application.
I seem to be having difficulty doing this. Might anybody know how I can accomplish this?
Thanks and hope to hear from you soon,
Katie
↧
setting the deafult geodatabase
I have changed the default geodatabase setting in the advanced settings and when hitting the default geodatabase button I am always brought to the location on my c drive. I thought ESRI fixed this but I have had this problem for months. Does anyone know a work around?
↧
↧
Google earth .kml to .shp file projection error? UK users??
Hello,
I've been given some .kml files containing polygons that someone has created within google earth.
This would not be my personal way of doing things.
I've been asked to project these .kml files in British National Grid.
However when projected they are not in the same position as in Google Earth.
Does anyone have experience of changing from these projections that could help me out?
I've been given some .kml files containing polygons that someone has created within google earth.
This would not be my personal way of doing things.
I've been asked to project these .kml files in British National Grid.
However when projected they are not in the same position as in Google Earth.
Does anyone have experience of changing from these projections that could help me out?
↧
Geospatial PDF Export Issues
I am trying to find a way to change the field that is listed in the model tree section of the PDF. If you look at the first image, you will see that each route is labeled by it's route name. If you look at the next image, the routes names are incomplete. The last image has all routes named feature.
I know I to control which attributes are exported by going to Layer Properties and selecting in the Fields tab. However, I can't figure out how do I control what is shown in the model tree.
Thanks for your help.
Attachment 33785Attachment 33787Attachment 33788
I know I to control which attributes are exported by going to Layer Properties and selecting in the Fields tab. However, I can't figure out how do I control what is shown in the model tree.
Thanks for your help.
Attachment 33785Attachment 33787Attachment 33788
↧
How to turn off snapping of elements/neatline?
Hi friends,
I am finding it very difficult to orient various elements on my layout correctly because they keep snapping to each other (causing weird overlay issues when printing). I would like to turn off this feature but it seems that the snapping controls only work for editing points and features etc... I cannot seem to find a way to turn off snapping of layout elements (like legend, neatlines, pictures, text, etc...).
Any ideas?
Thanks friends!
I am finding it very difficult to orient various elements on my layout correctly because they keep snapping to each other (causing weird overlay issues when printing). I would like to turn off this feature but it seems that the snapping controls only work for editing points and features etc... I cannot seem to find a way to turn off snapping of layout elements (like legend, neatlines, pictures, text, etc...).
Any ideas?
Thanks friends!
↧
Windows 8
Just curious if Arc interfaces well with the Windows 8 program. I know it works well with Windows 7, but would like some information
about Windows 8 for those who this.
about Windows 8 for those who this.
↧
↧
Capabilities not listing anything except "Feature Access" when sharing a map document
I'm trying to share a map document .mxd with some data in a .gdb to an ArcGIS 10.2 server. I go through the File > Share As > Service, but when viewing the Service Editor dialog the Capabilities tab shows only "Feature Access" and not "Mapping"/"Network Analysis" etc that I would normally expect.
Analysing the service gives an error "00090: Feature service requires a registered database" although I am unable to register a database (I have never needed to do this before with the 9.3, 10.0 or 10.1 server we test against). The folders the .gdb and .mxd are available to the "everyone" user group and I've tried doing this remotely with ArcMap 10.2 on my laptop and the same on the ArcGIS server itself.
I'm pretty much at a loss now. Can anyone shed some light on why this is happening?
Cheeers,
Chris
Attachment 33806
Analysing the service gives an error "00090: Feature service requires a registered database" although I am unable to register a database (I have never needed to do this before with the 9.3, 10.0 or 10.1 server we test against). The folders the .gdb and .mxd are available to the "everyone" user group and I've tried doing this remotely with ArcMap 10.2 on my laptop and the same on the ArcGIS server itself.
I'm pretty much at a loss now. Can anyone shed some light on why this is happening?
Cheeers,
Chris
Attachment 33806
↧
Issues in publishing Maps with Join
I am trying to publish a Map with a join where the table is in .xlsx format.
But I got the following error while I tried to publish.
SEVERITY STATUS CODE DESCRIPTION
High Unresolved 00099 Layer has a join with an unsupported data source
I would appreciate any help which could help me progress with regard to solving the issue.
P.S: I published the map just with the join
But I got the following error while I tried to publish.
SEVERITY STATUS CODE DESCRIPTION
High Unresolved 00099 Layer has a join with an unsupported data source
I would appreciate any help which could help me progress with regard to solving the issue.
P.S: I published the map just with the join
↧
arcgis 10.2.1; cant export to PDF?
does anyone else's arcgis 10.2.1 crash every time they try to export a PDF?
the same mxd's made PDF's just fine in 10.1.
any ideas?
thanks,
max
edit: figured it out... the default export style is a "production" pdf (whatever that is)... if you switch to a normal pdf no more crashing.
the same mxd's made PDF's just fine in 10.1.
any ideas?
thanks,
max
edit: figured it out... the default export style is a "production" pdf (whatever that is)... if you switch to a normal pdf no more crashing.
↧
Cannot share mxd as runtime content. General Function Failure
I'm trying to share my mxd as runtime content using ArcGIS Desktop 10.2.1. I followed the steps here, however everytime I try to generate the output I get an error message that reads as "General Function Failure"
↧
↧
Bing Maps works fine at first, then gets slow
I've been trying to get Bing Maps layers to work in ArcMap. I have a Bing Maps key, I load the layers using the "Add Data From ArcGIS Online" command, and it works great at first. Response time when panning and zooming the Bing Maps layer is good.
But after a while the behavior suddenly changes. The response time when panning and zooming the Bing Maps layer gets much worse. It still works but it's so slow as to make using it tedious.
I ran Fiddler to analyze the HTTP requests ArcMap was making. When I first load the Bing Maps layer it makes requests to virtualearth.net like I expect. But when the slowdown occurs I see a lot of requests to serverapi.arcgisonline.com which weren't occurring before. The request path is always /veadaptor/production//services/identity/clientip and there are two such requests for every tile request, a HEAD followed by a GET. I think these requests to serverapi.arcgisonline.com are what slows down performance so much.
At this point I save my project, exit ArcMap, then run ArcMap and open the project. Performance of the Bing Maps layer is great again until some time passes and those requests to serverapi.arcgisonline.com begin again.
Does anyone know why this happens? Why does ArcMap relentlessly query serverapi.arcgisonline.com for every tile request to Bing Maps?
But after a while the behavior suddenly changes. The response time when panning and zooming the Bing Maps layer gets much worse. It still works but it's so slow as to make using it tedious.
I ran Fiddler to analyze the HTTP requests ArcMap was making. When I first load the Bing Maps layer it makes requests to virtualearth.net like I expect. But when the slowdown occurs I see a lot of requests to serverapi.arcgisonline.com which weren't occurring before. The request path is always /veadaptor/production//services/identity/clientip and there are two such requests for every tile request, a HEAD followed by a GET. I think these requests to serverapi.arcgisonline.com are what slows down performance so much.
At this point I save my project, exit ArcMap, then run ArcMap and open the project. Performance of the Bing Maps layer is great again until some time passes and those requests to serverapi.arcgisonline.com begin again.
Does anyone know why this happens? Why does ArcMap relentlessly query serverapi.arcgisonline.com for every tile request to Bing Maps?
↧
NIM089961 Buffering fails with an error: 000599
NIM089961 Buffering fails with an error: "000599: Falls outside of output geometry domains" if the 'OUTSIDE_ONLY' option is turned on and dissolve is not used.
It seems like this issue was not resolved fully. I am running a simple buffer to a line feature class with the dissolving option enabled with no luck. The same error is returned every time the operation is executed.
It seems like this issue was not resolved fully. I am running a simple buffer to a line feature class with the dissolving option enabled with no luck. The same error is returned every time the operation is executed.
↧
ArcScene. Problem with displaying polygons.
Hi!
I have problem with proper displaying polygons on ArcScene.
On ArcMap everything is OK. I have been trying do something with rendering at Properties but it did not help.
ArcMap >> http://i.imgur.com/nSlQfgL.png
ArcScene >> http://i.imgur.com/4IxQWuG.png
This thinner polygons (between this larger) were created by 'Poly to line' (then created small buffer from this lines).
Sometimes when I am adding date all display proper for some times (until I change the view).
Ps. I have ArcMAp 10.2.1. Everything with Base Height is OK.
Thx for any help.
I have problem with proper displaying polygons on ArcScene.
On ArcMap everything is OK. I have been trying do something with rendering at Properties but it did not help.
ArcMap >> http://i.imgur.com/nSlQfgL.png
ArcScene >> http://i.imgur.com/4IxQWuG.png
This thinner polygons (between this larger) were created by 'Poly to line' (then created small buffer from this lines).
Sometimes when I am adding date all display proper for some times (until I change the view).
Ps. I have ArcMAp 10.2.1. Everything with Base Height is OK.
Thx for any help.
↧
Importing .sid file and converting to .TIFF
Hello,
For a current project, I have received a .sid file of an aerial map. The study area is very large, and the image size is 4.9 megabytes.
I would like to import this .sid file into ArcMap, and convert into a high resolution .TIFF (approximately 10000 x 10000)
Is there a way to do this in ArcMap? And if it cannot be done in ArcMap, does anybody have any experience with this type of file conversion?
Thanks,
Katie
For a current project, I have received a .sid file of an aerial map. The study area is very large, and the image size is 4.9 megabytes.
I would like to import this .sid file into ArcMap, and convert into a high resolution .TIFF (approximately 10000 x 10000)
Is there a way to do this in ArcMap? And if it cannot be done in ArcMap, does anybody have any experience with this type of file conversion?
Thanks,
Katie
↧
↧
Create Mobile Cache Help
I'm working in 10.1 SP1. I am trying to create a mobile cache for some field work but every time I run the tool from Mobile Tools it returns 0 (zero) data. I can't figure out what's wrong and what Esri has in the Help is not helpful (link below).
I need a by the number help- 1. your data should be in this format, 2. do this, 3. do that, etc. etc.
[URL="http://resources.arcgis.com/en/help/main/10.1/index.html#//003z00000005000000"]
I need a by the number help- 1. your data should be in this format, 2. do this, 3. do that, etc. etc.
[URL="http://resources.arcgis.com/en/help/main/10.1/index.html#//003z00000005000000"]
↧
Adding X,Y coordinates from Excel
Before I get into my topic of discussion, I should preface by saying that I am a beginner to the arcmap 10.1 software, so please excuse
any "newb" comments I might make.
Basically, I am trying to construct somewhat simple map of the United States that displays the
location of colleges that athletes from my school have gone onto transfer to. I am using a USA topographic map that I added
through ArcGIS online and the map was created by ESRI. The projected coordinate system for this map is "WGS_1984_Web_Mercator_Auxiliary_Sphere," and it's map units are in meters.
I created an excel spreadsheet with all the necessary information I need (name of student, name of the school, and the x and y
coordinates for each of their respective schools). When I add the excel spreadsheet document to my map using the "Add X,Y Data"
function, a new layer appears in my table of contents with all of my information included in the attributes table. The problem is no
points appear on my map whatsoever. It's not that they're in the wrong place, they just don't show up at all.
Like I mentioned before, the units used for this map is in meters, so does this mean that my x and coordinates must also be in
meters or can I still use decimal degrees for my coordinates? Either way, I tried using both, to no avail. Also, my excel spreadsheet is saved as a .xlsx file, if that makes any difference. If anyone has any insight or suggestions into this matter you would be helping me a lot and I would greatly appreciate it. Thank you in advance.
any "newb" comments I might make.
Basically, I am trying to construct somewhat simple map of the United States that displays the
location of colleges that athletes from my school have gone onto transfer to. I am using a USA topographic map that I added
through ArcGIS online and the map was created by ESRI. The projected coordinate system for this map is "WGS_1984_Web_Mercator_Auxiliary_Sphere," and it's map units are in meters.
I created an excel spreadsheet with all the necessary information I need (name of student, name of the school, and the x and y
coordinates for each of their respective schools). When I add the excel spreadsheet document to my map using the "Add X,Y Data"
function, a new layer appears in my table of contents with all of my information included in the attributes table. The problem is no
points appear on my map whatsoever. It's not that they're in the wrong place, they just don't show up at all.
Like I mentioned before, the units used for this map is in meters, so does this mean that my x and coordinates must also be in
meters or can I still use decimal degrees for my coordinates? Either way, I tried using both, to no avail. Also, my excel spreadsheet is saved as a .xlsx file, if that makes any difference. If anyone has any insight or suggestions into this matter you would be helping me a lot and I would greatly appreciate it. Thank you in advance.
↧
ArcScene disappearing DEM's!
Hey All,
So I want to be able to view my DEM that I am using in ArcGIS10 in 3D. However, the file is very large and when I add it to ArcScene it computes it so that it only had two values under symbology.
However, I have smaller grids of the DEM that I have tried to import into Arcscene (will merge them later) however, I can't see them? Anybody know why this might be?
Thanks for any help in advance :D
Katie
So I want to be able to view my DEM that I am using in ArcGIS10 in 3D. However, the file is very large and when I add it to ArcScene it computes it so that it only had two values under symbology.
However, I have smaller grids of the DEM that I have tried to import into Arcscene (will merge them later) however, I can't see them? Anybody know why this might be?
Thanks for any help in advance :D
Katie
↧